Ubiquiti Networks launches the PowerBeam ISO, an airMAX Bridge that is ideal for deployments requiring maximum performance and RF isolation.
Improved Noise ImmunityThe PowerBeam ISO directs RF energy in a tighter beamwidth, and its integrated isolator design improves RF isolation to spatially filter out interference. With its combination of focused beam directivity and RF isolation, the PowerBeam ISO blocks noise to improve noise immunity. This is especially important in an area crowded with other RF signals of the same or similar frequency.
Integrated Radio DesignUbiquiti's InnerFeed technology integrates the radio into the feedhorn of an antenna, so there is no need for a cable. This improves performance because it eliminates cable losses. Providing high performance and innovative mechanical design at a low cost, the PowerBeam ISO is extremely versatile and cost-effective to deploy.
airMAX Technology IncludedUnlike standard Wi-Fi protocol, Ubiquiti’s Time Division Multiple Access (TDMA) airMAX protocol allows each client to send and receive data using pre-designated time slots scheduled by an intelligent AP controller. This time slot method eliminates hidden node collisions and maximizes airtime efficiency, so airMAX technology provides performance improvements in latency, noise immunity, scalability, and throughput compared to other outdoor systems in its class.
Intelligent QoSPriority assigned to voice/video for seamless streaming.
ScalabilityHigh capacity and scalability.
Passive PoEUsing PoE technology allows to transmit data stream and power / energy through the enthernet cable which integrates the PowerBeam M5-300-ISO to your network enviroment. There is no need to to install any extra wired power cord. A 24V, 0.5A PoE Injector is included.
Robust outdoor designThe mechanical design of the PowerBeam M5 300 ISO provides weatherproof performance. Acitivity and signal strength LED's provided for installers. Enhanced RF and Ethernet ESD/Surge protection enables prolonged operation in harshest environments. The PowerBeam M5 300 ISO is designed for mast or pole installation.
AirOS SoftwareAirOS is the intuitive, versatile, highly developed Ubiquiti firmware technology. It is exceptionally intuitive and was designed to require no training operate. Behind the user webinterface is a powerful firmware architecture which enables hi-performance networking. Additionally, the AirControl application allows operators to centrally manage 100's of devices.
Long Distance and TCP/IP ThroughputThe PowerBeam M5 300 ISO is capable of high speed, carrier-class links up to 20km with real TCP/IP throughput of 150Mbps+.
Technical Data:
Manufacturer / Product: | Ubiquiti Networks / PowerBeam M5-300 |
Processor Specs: | Atheros MIPS 74KC, 560 MHz |
Memory Information: | 64MB DDR2, 8MB Flash |
Operating System: | AirOS |
Networking Interface: | 1 x 10/100 BASE-TX (Cat. 5, RJ-45) |
Frequency Band: | Worldwide: 5170 - 5875 MHz USA: 5725 - 5850 MHz |
Supported Standards: | IEEE 802.11a: 54MBit IEEE 802.11n: 300MBit |
TX Power: | max. 24dBm |
RX Sensitivity: | min. -94dBm |
TCP/IP Throughput: | 150Mbps+ |
Range: | up to 20km+ |
Antenna: | 22dBi Dual-Linear Backfire Antenna |
max. Power Consumption: | 8 Watt |
Power Method: | Passive Power over Ethernet PoE Injector is included! |
Power Input: | 18V - 26V |
ESD/EMP Protection: | 24KV radio frequency and ethernet electrostatic discharge (ESD) protection |
Dimensions: | 36.4 x 36.4 x 27.6 cm |
Weight: | 2.55 kg |
max. Wind Load | 210 N @ 200 km/h (47 lbf @ 125 mph) |
Operating Temperature: | -40°C to +70°C |
Operating Humidity: | 5 to 95% non condensing |
Shock and Vibration:: | IEC 68-2-6, IEC 68-2-14 |
Scope of delivery:
1 x Ubiquiti PowerBeam M5 300 ISO |
1 x 24V/0.5A - PoE Injector |
1 x Mounting Kit |